Zoeken
Basic thread repair kits
Basic version of the repair kit for inserted threads, essential, practical and functional to meet the needs of maintenance technicians.
Kit composition:
- 1 installation tool
- 1 finishing tap
- 1 drill bit (except for M12/M14/M16)
- 1 miter saw (except for M12/M14/M16)
- 10/15/20 1.5D threads
N8671M03X0,5, N8671M04X0,7, N8671M05X0,8, N8671M06X1,0, N8671M08X1,0, N8671M08X1,25, N8671M10X1,0, N8671M10X1,25, N8671M10X1,5, N8671M12X1,25, N8671M12X1,75, N8671M14X2,0, N8671M16X2,0
Meer details
|
Van €36.14
|
Bolt anchor for cracked concrete and seismic applications FAZ II FISCHER
The FAZ ll tried and tested expansion clip enables the highest load bearing capacity. Thus fewer fixing points and smaller anchor plates are required.
The reduced anchorage depth allows for significantly reduced drill hole depths and reduces the number of reinforcement hits. This allows for a noticeably quicker installation. Fewer hammer blows when hammering in the anchor, together with the low torque slippage, ensure a noticeably simple and comfortable setting process. The international approvals guarantee maximum safety and the best performance. These approvals even cover use in earthquake zones (sismic). Building materials Approved for concrete C20/25 to C50/60, cracked. Concrete C20/25 to C50/60, non-cracked. Also suitable for concrete C12/15, natural stone with dense structure.
N823008010, N823008050, N823010010, N823010050, N823012010, N823012020, N823012030, N823012050, N823016025, N823016050, N823016100
Meer details
|
Van €1.25
|
Bolt anchor zinc-plated steel for non-cracked concrete FBN II FISCHER
The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required.
The reduced anchorage depth reduces the drill hole depth. This minimizes the amount of time needed for installation whilst increasing flexibility. The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility. Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation. The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment. Building materials Approved for concrete C20/25 to C50/60, non cracked Also suitable for concrete C12/15 and natural stone with dense structure
N822508005, N822508010, N822508020, N822508030, N822508050, N822510010, N822510020, N822510030, N822510050, N822510070, N822510100, N822512010, N822512020, N822512030, N822512050, N822516025, N822516050, ...
Meer details
|
Van €0.75
|
Bolt anchors zinc plated steel for non-cracked concrete VORPA VE.7CE
Mechanical anchors in galvanized steel with metal clamp and expansion cone ETA-certified option 7 for non-cracked concrete C20 / 25 - C50 / 60. Suitable for anchoring in heavy carpentry, plant engineering, construction, laying of stairs and railings.
Features: - European technical approvement - Thread diameter equal to drilling diameter - Head reinforced to avoid damaging the thread during installation - Special shape expansion bush to make the expansion soft and progressive - Ensures high load values and rapid installation even without moving the object to be fixed Support materials Approved for non-cracked concrete with strength class from C20/25 to C50/60. Also suitable for non-cracked concrete with strength class C12/15 and compact natural stone.
N822708080, N822708095, N822710075, N822710105, N822710120, N822712110, N822712120, N822712140, N822712200, N822716150, N822716175, N822716220, N822710090
Meer details
|
Van €0.67
|
Bolt anchors zinc plated steel for non-cracked concrete VORPA VE.A
Mechanical anchors in galvanized steel with metal clamp and expansion cone. Extra-long thread ideal for all type of carpentry, plant and building applications.
- Features: - Thread diameter equal to drilling diameter - Reinforced head to avoid damaging the thread during installation - Special shape expansion bush to make the expansion soft and progressive - It guarantees high load values and rapid installation even without moving the object to be fixed Support materials Recommended for non-cracked concrete with strength class C20/25
N822308075, N822308090, N822310080, N822310100, N822310120, N822310140, N822312090, N822312110, N822312145, N822316145, N822316175, N822320170
Meer details
|
Van €0.62
|
Brass fixing PO FISCHER
Dowel with knurled body for excellent adhesion to hole walls, shallow installation depth, simple for light installations and air ducts, metric thread, threaded rods, screws and all threaded accessories can be fitted.
Building materials
Concrete and natural stone with dense structure.
N821006, N821008, N821010, N821012
Meer details
|
Van €0.58
|
Drill bushes DIN 172 long series KING
DRILL BUSHES DIN 172 – LONG SERIES
N853010, N853012, N853013, N853014, N853016, N853020, N853025, N85303, N853030, N85304,5, N85305, N85306, N85306,5, N85307, N85308, N85308,5
Meer details
|
Van €3.21
|
Drill bushes DIN 172 short series KING
DRILL BUSHES DIN 172 – SHORT SERIES
N851010, N851010,5, N851011, N851012, N851014, N851015, N851016, N85102,2, N85102,3, N85102,4, N85102,5, N851020, N851022, N851025, N85103,3, N85103,5, N851030, ...
Meer details
|
Van €2.68
|
Drill bushes DIN 179 long series KING
DRILL BUSHES DIN 179 – LONG SERIES
N852010, N852011, N852012, N852014, N852018, N85202, N852020, N852022, N852025, N852026, N85203, N85203,2, N85203,5, N852030, N85204, N85205, N85206, ...
Meer details
|
Van €2.14
|
Drill bushes DIN 179 short series KING
DRILL BUSHES DIN 179 – SHORT SERIES
N850010, N850010,5, N850012, N850014, N850016, N850017, N850018, N85002, N850020, N850030, N85004, N85005, N85005,5, N85006, N85006,1, N85006,25, N85006,5, ...
Meer details
|
Van €2.04
|
Heavy-duty anchor for non-cracked concrete SLM with screw TE 8.8 zinc-plated FISCHER
The optimized geometry minimizes setting energy and allows for use in extremely narrow spaces. This allows for user-friendly installation.
The three-part expansion sleeve creates even load distribution, thus allowing small edge and axial spacing. Thus the SLM is extremely flexible. The metric internal thread allows to use standard screws or threaded rods for the ideal adaptation to suit the intended use. The red plastic cap protects against soiling and thus ensures free-running of the thread. Zinc version with TE screw in steel 8.8. Building materials Approved for, concrete C20/25 to C50/60, non-cracked. Also suitable for, concrete C12/15 natural stone with dense structure.
N822006, N822008, N822010, N822012
Meer details
|
Van €1.72
|
Heavy-duty anchor TA M-S for medium loads with screw TE 8.8 zinc-plated FISCHER
The optimized geometry minimise setting energy and allows for use in extremely narrow spaces. This allows for user-friendly installation. The three-part expansion sleeve creates even load distribution, thus allowing small edge and axial spacing. Thus the TA M is extremely flexible.
The metric internal thread allows to use standard screws or threaded rods for the ideal adaptation to suit the intended use. The red plastic cap protects against soiling and thus ensures free-running of the thread. Versions zinc-plated steel.
Building materials
Approved for concrete C20/25 to C50/60, noncracked, also suitable for concrete C12/15 natural stone with dense structure.
N821516, N821508, N821510, N821512
Meer details
|
Van €1.69
|
Mandrels for wire thread inserts
Mandrels for wire thread inserts. Free rod insertion version.
N8650M10X1,0, N8650M10X1,5, N8650M12X1,0, N8650M12X1,5, N8650M12X1,75, N8650M14X1,25, N8650M14X2,0, N8650M16X1,5, N8650M16X2,0, N8650M18X2,5, N8650M2,5X0,45, N8650M20X2,5, N8650M22X2,5, N8650M24X3,0, N8650M2X0,4, N8650M3X0,5, N8650M4X0,7, ...
Meer details
|
Van €50.09
|
Nylon anchor SX-S model with rim and screw Pozidriv FISCHER
The 4-way expansion provides the optimum force distribution in the material, and offers high load-bearing capacities in solid and hollow building materials.
The expansion-free plug neck prevents the creation of expansion forces on the material surface whilst screwing in the screw. This helps to prevent damage to tiles and plaster. The pronounced rim prevents the plug from slipping into the drill hole, thus allowing for a simple installation. The greater anchorage depth of the SX means that the plug is especially suited to fixings in hollow building materials, aerated concrete and to bridge plaster Building materials Concrete, vertically perforated brick, hollow block made from lightweight concrete, cavity floor slabs made of brick, concrete, perforated sand-lime brick, solid sand-lime brick, natural stone with dense structure, aerated concrete, solid panel made from gypsum, solid brick made from lightweight concrete, solid brick. The price shown refers to a pack of 100 pieces
N820505, N820506, N820508, N820510
Meer details
|
Van €17.83
|
Self-tapping thread inserts - galvanized steel
Galvanized case hardened steel self-tapping thread inserts with internal and external thread. Ideal for producing metric screw threads that are capable of supporting heavy loads. Vibration and wear resistant. Suitable for materials with low shear strength such as aluminium alloys, brass, bronze, cast iron, Duroplast and thermoplastic resins.
The thread inserts have a cutting slot and a tapered bottom, which allows them to join together. When screwed in, they cut their own threads inside the hole, ensuring that it is fastened firmly and securely.
N86020306, N86020408, N86020510, N86020612, N86020614, N86020815, N86021018, N86021222, N86021424, N86021622
Meer details
|
Van €0.34
|
Self-tapping thread inserts - stainless steel
stainless steel 1.305 AISI 303 self-tapping thread inserts with internal and external thread. Ideal for producing metric screw threads that are capable of supporting heavy loads. Vibration and wear resistant. Suitable for materials with low shear strength such as aluminium alloys, brass, bronze, cast iron, Duroplast and thermoplastic resins.
The thread inserts have a cutting slot and a tapered bottom, which allows them to join together. When screwed in, they cut their own threads inside the hole, ensuring that it is fastened firmly and securely.
N86030306, N86030408, N86030510, N86030612, N86030614, N86030815, N86031018, N86031222
Meer details
|
Van €0.66
|
Taps for wire thread inserts
Taps for hand or machine use.
N8630M10X1,25, N8630M10X1,50, N8630M12X1,0, N8630M12X1,25, N8630M12X1,5, N8630M12X1,75, N8630M14X1,25, N8630M14X1,5, N8630M14X2,0, N8630M16X1,5, N8630M16X2,0, N8630M18X2,5, N8630M2,5X0,45, N8630M20X2,5, N8630M22X2,5, N8630M24X3,0, N8630M2X0,4, ...
Meer details
|
Van €13.58
|
Thread inserts repair kits
Thread Inserts repair kits studied to satisfy the needs of the technicians of the maintenance, practical and functional.
Compostion of kit: - 1 cutter - 1 installation tool - 1 finishing tap - 1 drill bit - 10/15/20 threads 1,5xD
N8670M03X0,5, N8670M04X0,7, N8670M05X0,8, N8670M06X1,0, N8670M08X1,0, N8670M08X1,25, N8670M10X1,0, N8670M10X1,25, N8670M10X1,5, N8670M12X1,25, N8670M12X1,75, N8670M14X2,0, N8670M16X2,0
Meer details
|
Van €84.20
|
Thread Inserts repair kits multidimension
Thread Inserts repair kits multidimension studied to satisfy the needs of the technicians of the maintenance, pratical and functional.
Composition of the kit:
- 2 setting tools respectively for M6-M8 and M10-M12 threads
- 4 finishing taps for M6-M8-M10-M12 threads
- 3 thread cutters M6-M8-M10-M12
- 4 M6-M8-M10-M12 drill bits
- Threads 10/15/20 1.5D
N8690KITMULTI
Meer details
|
Van €389.25
|
Universal plug FU with rim and screw Pozidriv FISCHER
The universal fixing FU is suitable for through and non-through installations.
In solid building materials the screwing results in a complete expansion of the fastener against the hole wall, in perforated building materials the fastener body expands by undercutting into the cavity.
Building materials
Concrete, gypsum plasterboard and gypsum fibre boards, vertically perforated brick, hollow block made from lightweight concrete, cavity floor slabs made of brick, concrete, perforated sand-lime brick, solid sand-lime brick, aerated concrete.
The price shown refers to a pack of 100 pieces
N82070635, N82070645, N820708, N820710
Meer details
|
Van €31.82
|
Wire thread inserts stainless steel M
Very high mechanical strength stainless steel wire thread inserts (approx. 145 kg/mm²).
Their typical design, in the shape of a spring, forms two perfectly concentric threads, one external and the other internal. The external one allows the wire thread insert to be inserted in a hole threaded with a specific tap, while the internal thread accommodates a screw with maximum precision.
N86110210, N86110215, N86110220, N86110225, N86110230, N861102510, N861102515, N861102520, N861102525, N861102530, N86110310, N86110315, N86110320, N86110325, N86110330, N86110410, N86110415, ...
Meer details
|
Van €0.36
|
Wire thread inserts stainless steel MF
Very high mechanical strength stainless steel wire thread inserts (approx. 145 kg/mm²).
Their typical design, in the shape of a spring, forms two perfectly concentric threads, one external and the other internal. The external one allows the wire thread insert to be inserted in a hole threaded with a specific tap, while the internal thread accommodates a screw with maximum precision.
N86120810015, N86120810020, N86120810025, N86120810030, N86121010010, N86121010015, N86121010020, N86121010025, N86121010030, N86121012510, N86121012515, N86121012520, N86121012525, N86121012530, N86121210010, N86121210015, N86121210020, ...
Meer details
|
Van €0.42
|