Winkelwagen
  • U heeft geen artikelen in uw winkelwagen.
Cataloghi

Carbide drills

Toon als
Sorteren op
Geometry: Advanced flute design for high performance in stainless steel. Point angle: 140° Surface treatment: Application: Machining of long and short chip materials. Recommended for drilling hol...
A008810, A008810,2, A008810,2W, A008810,3, A008810,3W, A008810,5, A008810,5W, A008810,8, A008810,8W, A008810W, A008811, A008811,8, A008811,8W, A008811W, A008812, A008812,5, A008812,5W, ...
Meer details
Geometry: Advanced helix, concave, geometry of the cutting edges, self-centering sharpening Point angle: 135° Surface treatment: Application: Machining of long and short chipping materials, such ...
A004503,0, A004503,3, A004503,5, A004503,7, A004503,8, A004504,0, A004504,2, A004504,5, A004504,8, A004505,0, A004505,5, A004505,8, A004506,0, A004506,5, A004506,8, A004507,0, A004507,5, ...
Meer details
Geometry: Advanced flute geometry, designed for optimal chip evacuation on a broad range of materials Point angle: 118° Surface treatment: Bright Application: Drill suited for machining on a wide ...
A00030,2, A00030,3, A00030,4, A00030,5, A00030,6, A00030,7, A00030,8, A00030,85, A00030,9, A00031, A00031,05, A00031,1, A00031,15, A00031,2, A00031,25, A00031,3, A00031,4, ...
Meer details
Geometry: Special web thinning, rounded flute profile Point angle: 118° Surface treatment: Bright Application: Indicated for CN machines, materials with R ≤ 1000 N/mm². : 5xD : - : HM
A10801, A10801,1, A10801,2, A10801,3, A10801,4, A10801,5, A10801,6, A10801,7, A10801,8, A10801,9, A10802, A10802,1, A10802,2, A10802,3, A10802,4, A10802,5, A10802,6, ...
Meer details
Geometry: Rake angles and offset angles designed for steels and cast iron Point angle: Surface treatment: Application: For tapping pre-holes and countersinking on materials as carbon steels, cas...
A1780M10, A1780M12, A1780M14, A1780M16, A1780M3, A1780M4, A1780M5, A1780M6, A1780M8
Meer details
A1811KIT
Meer details
Van €292.28
Taps drill-out tools in solid carbide WRK This solid carbide tool was designed to extract broken taps from holes.
Machining is normally run dry.

For best centring, follow the procedure below:

- (1) Flatten the broken tap, using a larger tool or
a same-sized hand mill.
- (2) Select a suitable tap destroying tool and execute the work
being careful that the processed rigidity is the maximum.
Recommended cutting speed not greater than 45 m/mm and
feed rate from 0.03 to 0.05 mm.
- (3) Remove the tap pieces left along the walls using
a sharp tool.
- (4) When finished, we recommend reprocessing the hole with a drill
of the same size as the pre-tapping hole.
A181012, A18103, A18104, A18104,5, A18105, A18106, A18108, A181010
Meer details