Zoeken
Cataloghi
- Alpa
- DORMER
- GERARDI
- IMET
- KEMMLER
- Link
- PRAMET
- SANDVIK
- Vardex
- Voelkel
- Walter
- SANDVIK_COROMANT
Solid carbide drills
Toon als
Sorteren op
|
Geometry: Special web thinning, rounded flute profile, self-centering point geometry Point angle: 118° Surface treatment: Bright Application: Indicated for CN machines, materials with R ≤ 1000 N/m...
A12301, A12301,1, A12301,2, A12301,3, A12301,4, A12301,5, A12301,6, A12301,7, A12301,8, A12301,9, A123010, A123010,2, A123010,5, A123011, A123011,5, A123012, A123012,5, ...
Meer details
|
Van €6.96
|
|
Geometry: Advanced flute design for high performance Point angle: 140° Surface treatment: Devil Application: Machining of short or long chip materials. Recommended for machining carbon steel up to...
A000510, A000510,2, A000510,2W, A000510,5, A000510,5W, A000510W, A000511, A000511,5, A000511,5W, A000511W, A000512, A000512,5, A000512,5W, A000512W, A000513, A00053, A00053,1, ...
Meer details
|
Van €39.26
|
|
Geometry: Advanced flute design for high performance Point angle: 140° Surface treatment: Devil Application: Short or long chip materials machining. Recommended for carbon steel up to 1100 N/mm² a...
A000710, A000710,2, A000710,2W, A000710,5, A000710,5W, A000710W, A000711, A000711,5W, A000711W, A000712, A000712,5, A000712,5W, A000712W, A000713, A000713W, A00073,1, A00073,1W, ...
Meer details
|
Van €59.92
|
|
Geometry: Advanced flute geometry, designed for optimal chip evacuation on a broad range of materials Point angle: 118° Surface treatment: Bright Application: Drill suited for machining on a wide ...
A00030,2, A00030,3, A00030,4, A00030,5, A00030,6, A00030,7, A00030,8, A00030,85, A00030,9, A00031, A00031,05, A00031,1, A00031,15, A00031,2, A00031,25, A00031,3, A00031,4, ...
Meer details
|
Van €16.00
|
|
Geometry: Rake and sharpening angles designed for generic steel and cast iron machining Point angle: 130° Surface treatment: Bright Application: Deep drilling specifically for mould steels with Rm...
A008010400, A008010600, A008010800, A008012400, A008012500, A008012600, A008012700, A008012800, A008016500, A008016800, A00806300, A00806500, A00808800
Meer details
|
Van €144.20
|
|
Geometry: Special web thinning, rounded flute profile Point angle: 118° Surface treatment: Bright Application: Indicated for CN machines, materials with R ≤ 1000 N/mm².
A10801, A10801,1, A10801,2, A10801,3, A10801,4, A10801,5, A10801,6, A10801,7, A10801,8, A10801,9, A10802, A10802,1, A10802,2, A10802,3, A10802,4, A10802,5, A10802,6, ...
Meer details
|
Van €5.37
|
|
Taps drill-out kit in solid carbide WRK
TAPS DRILL-OUT KIT
A1811KIT
Meer details
|
Van €292.28
|
|
Taps drill-out tools in solid carbide WRK
This solid carbide tool was designed to extract broken taps from holes.
Machining is normally run dry.
For best centring, follow the procedure below:
- (1) Flatten the broken tap, using a larger tool or
a same-sized hand mill.
- (2) Select a suitable tap destroying tool and execute the work
being careful that the processed rigidity is the maximum.
Recommended cutting speed not greater than 45 m/mm and
feed rate from 0.03 to 0.05 mm.
- (3) Remove the tap pieces left along the walls using
a sharp tool.
- (4) When finished, we recommend reprocessing the hole with a drill
of the same size as the pre-tapping hole.
A181012, A18103, A18104, A18104,5, A18105, A18106, A18108, A181010
Meer details
|
Van €56.95
|